America's Largest Supplier of RV & Teardrop Trailer Parts
Part number: HT16
PVC 1" Insert Trim Molding
PVC Insert is applied to Insert trim to provide UV protection, prevent water damage and PVC gives a professional finish hiding screws heads.
Price: Black Insert $0.30 a foot
Also available in white, grey or red
Price $0.35 a foot
Part number: HT17
93" Offset Insert Flat Trim Molding
Short leg: 1/4" x Width: 1-1/8" Long leg: 3/8"
Mill finish Offset flat molding is more flexible and will conform to some curved surfaces. Its used on roof edges or wall corners when creating a seal on exterior panels
(1" PVC Insert not included)
Price $14.85
Part number: HT09
Mill Finish Aluminum 93" Trim Edge Molding
Price $13.50
Part number HT09-01
Satin Anodized Aluminum 93" Trim Edge
Price 14.50
Sale: $2.00 Per 4' Stick shipping not included.
Part number: HT12-01
93" Flat Trim Insert Molding - Powder coated Black
Flat molding is used when creating a seal at the transitions of exterior panels, protecting against water intrusion. It can be used on the top or sides of the RV
(1" PVC Insert not included)
Price $15.85
Part number: HT11
93" Aluminum Insert Type Roof Edge Molding
1-1/8" Wide x 5/8" Leg
Corner molding is used when creating a seal at the edges of the exterior panels to protect against water leaks. It can be used on roof edges or wall corners.
(1" PVC Insert not included)
Price $14.85
Part number: HT11-01
93" Insert Roof Edge Molding - Powder coated Black
1-1/8" Wide x 5/8" Tall
Corner molding is used when creating a seal at the edges of the exterior panels to protect against water leaks. It can be used on roof edges or wall corners.
(1" PVC Insert not included)
Price $15.85
Part number: HT05
Offset Hurricane Hinge
2-Piece Extruded Aluminum Aluminum - Mill Finish!
Lower Profile Crown
Tighter "Nesting Pocket" within the Crown (less slop/play)
1/4" Lid-to-Roof Offset! (No need to notch wall)
The Offset Hurricane Hinge comes in several different lengths:
Prices:
4ft -$52.00 - free shipping
5ft -$71.00 - free shipping
6ft -$90.00 - free shipping
add $19.00 for each additional foot up to 8' maximum length
Packaging Fee applies: $15.00
1-1/8" Wide
Part number: HT10
Aluminum 93" Roof Edge Door Jamb Liner Molding
Price $14.85
Part number: HT15
Table Mounting Bracket
This RV Table Wall Mount is perfect for giving support to the table while allowing the table to still be removed
Sold in 30" Lengths - Free Shipping
30" Length - $24.50
Part number:
HT21 (10pc) (Black)
21.00 + shipping
HT21-01 (1pc) (Black)
2.30 each + shipping
HT22 (10pc) (Mill Finished)
17.00 + shipping
HT22-01 (1pc) (Mill Finished)
2.00 each + shipping
Black or Mill finished End caps
Apply end caps by fastening them on to the end of your Trailer trim molding using the screws provided. Trim caps prevent vinyl shrinkage while giving your project a clean professional look.
Roof side w/flat bar
5/8" Tall
Part number: HT14
6' Flexable Offset "T" Molding
Offset T trim is used when creating a seal at the transitions of exterior panels. (Galley hatch door)
Price $27.50 each
Part number: HT13
93" Flexable "T" Aluminum Molding
Price $18.95 each
Part number: HT17-01
Offset Insert Flat Trim Molding Powder coated Black
Short leg: 1/4" x Width: 1-1/8" Long leg: 3/8"
Offset flat molding is more flexible and will conform to some curved surfaces. Its used on roof edges or wall corners when creating a seal on exterior panels
(1" PVC Insert not included)
Price $15.85
1/4" Gap
Part number: HT11-02
93" Insert Roof Edge Molding - Black
1-1/8" Wide x 3/4" Leg
Corner molding is used when creating a seal at the edges of the exterior panels to protect against water leaks. It can be used on roof edges or wall corners
(1" PVC Insert not included)
Price $16.85
Part number:HT12
93" Flat Trim Insert Molding
Flat molding is used when creating a seal at the transitions of exterior panels, protecting against water leaks. It can be used on the top or sides of the RV
(1" PVC Insert not included)
Price $14.85
Hatch Side
1/4" Tall
3/8" Tall